 Rank: Advanced Member Groups: Registered
Joined: 04/05/2018(UTC) Posts: 71  Location: Buende Thanks: 1 times Was thanked: 17 time(s) in 9 post(s)
|
Hello!
I've to flash a BMW DME 17.2.G directly on bench. Can someone give me the diagram to connect the DME?
I've here a coding station with CAS emulator and ZGW or a connected FEM with key.
CU Oliver
|
|
|
|
|
HexTag/HexProg tool is the ultimate tool for Ecu Cloning/Ecu Tuning including MDG1 Ecu Cloning/MDG1 Ecu Tuning, BDM Read/write, Key renew and EEPROM Reset
Click here on HexTag for more info about HexProg Software
|
|
 Rank: Member Groups: Registered
Joined: 18/09/2020(UTC) Posts: 26
Thanks: 1 times Was thanked: 2 time(s) in 2 post(s)
|
this type of programming is done flexray. you must have a ZGW, with ZGW you must connect to the driver but not via can l and can h. this link is read, there are other pins for programming.
|
|
|
|
 Rank: Member Groups: Registered
Joined: 18/09/2020(UTC) Posts: 26
Thanks: 1 times Was thanked: 2 time(s) in 2 post(s)
|
this type of programming is done flexray. you must have a ZGW, with ZGW you must connect to the driver but not via can l and can h. this link is read, there are other pins for programming.check it out on newtis.info but you have to buy an access
|
|
|
|
 Rank: Advanced Member Groups: Registered
Joined: 04/05/2018(UTC) Posts: 71  Location: Buende Thanks: 1 times Was thanked: 17 time(s) in 9 post(s)
|
Hello!
I will not need any newtis, I have access to ISTA (and sgate, Air a.s.o.). :)
So only the two flexray wires and not the CAN H and CAN L? And power supply of course.
CU Oliver
|
|
|
|
 Rank: Member Groups: Registered
Joined: 18/09/2020(UTC) Posts: 26
Thanks: 1 times Was thanked: 2 time(s) in 2 post(s)
|
find in dme / dde two pins marked in ista as programming. connect them between the driver and the Zgw. zgw to autohex via flexray. and of course 12v for everything. you will program dme / dde anyway
|
|
|
|
 Rank: Advanced Member Groups: Moderator
Joined: 22/08/2015(UTC) Posts: 1,484  Location: Dubai Thanks: 584 times Was thanked: 1399 time(s) in 745 post(s)
|
Originally Posted by: Milkyway  Hello!
I've to flash a BMW DME 17.2.G directly on bench. Can someone give me the diagram to connect the DME?
I've here a coding station with CAS emulator and ZGW or a connected FEM with key.
CU Oliver Please see the attached diagram for MEVD1728 along with FEM made by one of our customer. MEVD172G pin out will be different from it but it will help you to identify what all pin need to be used.  fem and dme.png (143kb) downloaded 19 time(s).
|
 1 user thanked Autohex_II_BMW for this useful post.
|
|
|
 Rank: Advanced Member Groups: Registered
Joined: 04/05/2018(UTC) Posts: 71  Location: Buende Thanks: 1 times Was thanked: 17 time(s) in 9 post(s)
|
Hello!
Thx. As I can see, the DME 17.2.G has Flexray on Pin 33 and 34 on connector 1b and PT-Can on Pin 7 and 8. B+ is on 45 and ground on Pin 4 in 5b. So I will test it in this way and will report.
CU Oliver
|
|
|
|
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.
Important Information:
The Microtronik Autohex II forum uses cookies. By continuing to browse this site, you are agreeing to our use of cookies.
More Details
Close